Products
Homepage • Products • Copper Connect • Adsl
1.General structure
ADSL Module group is designed for unifying the voice input and high frequency input of internet access on the same subscriber line. In order to obtain this property there is one (pair) input from incoming side (for voice) and one other input from the adjacent contacts (for ADSL high and low frequencies) and the output from the opposite side (outgoing side) of the module. This feature is performed by the help of a splitter with a double side golden finger contact pub on which one side is in contact with inputs i.e voice and ADSL signal. Other side is in contact with the unified contacts.
As a result the unit serves as a unifier of voice and ADSL to the subscriber side of the line.
Benefits of ADSL Module group:
a) Splitters are inserted from the back side of the module which is being provided easy and continuous access to the cable side of Modules.Therefore cabling on front side is made easily with no any disturbing the other subscribers.
b) Splitters are hidden at the rear side to keep away from any mechanical touch disturbance etc. there is no danger of miscontact problem due to operator touch or vibration etc
c) The splitters place (rear side is accessible by the help of an hinge which provides easy access to the back
d) Splitters are positioned in the rear side inside of the metal cage to keep away from magnetic field effects.
e) Metal frame is made of stainless steel to avoid corrosion
f) Several cable grommets are provided to keep cables safe and free from cuts.
g) First 25 pairs are black and second 25 pairs are orange colored for easy distinction.
h) Capacity is 50 pairs (unified) for each group
i) There is a label on top of each unit and the bottom of body to note the Rack no /Sub rack No/ Cable ref etc.
ADSL POTS Splitter Unit designed by Kepkep Company. ADSL POTS splitter is implemented with the Voice Band Passing LOW pass filter to stabile separate voice signal from the composite band Asymmetrical Digital Subscriber Line (ADSL) data and voice. ADSL POTS Splitter protects POTS from interference signal, which is caused by ATU-R Modem and protects ATU-R Modem from signals related POTS. The Splitter should keep stable features with DC loop current 100 mA and keep balance itself in case of Ring tone.
The filter should be consisted of two level of low pass filter, which should be passive structure.
Insertion Loss
The insertion loss at 1KHz of the single low–pass filter, between the LINE and POTS interface attenuation maintain less than 0.3 dB, when the interfaces are terminated with the network of which fulfills the ITU-T G992.1 recommendation clause E.1.3
Insertion Frequency Distortion
The frequency distortion between LINE and POTS interface, relative to 1KHz, keep within ±1 dB over the frequency range from 200Hz to 4KHz. This fulfills the ITU-T G992.1 recommendation clause E.1.4.
Return Loss
The return loss of the POTS and LINE interface, measured against the impedance of the network with the opposite interface terminated with the same network, as follows:
200 Hz to 300 Hz with 600 Ohms >12 dB
300 Hz to 500 Hz with 600 Ohms >14 dB
500 Hz to 2000 Hz with 600 Ohms >18 dB
2000 Hz to 3400 Hz with 600 Ohms >14 dB
3400 Hz to 4000 Hz with 600 Ohms >12 dB
This fulfills the ITU-T G992.1 recommendation clause E.1.2.
Stop Band Attenuation
When measured between 100 Ohms termination and with the normal High–pass filter load, the stop band attenuation of the filter is higher than 50 dB between 32 KHz to 100 KHz.
Isolation
The DC resistance observed at the POTS interface does not exceed 50 Ohms when a short circuit is applied across the LINE interface, and shall not be less than 1 MOhms in the open circuit condition. This fulfills the ITUT G992.1 recommendation clause E.1.5.
Environmental Conditions
Operating temperature: -20º C / +55º C
Operating humidity: % 90 RH
Electrical Safety
There is no lightning and high voltage protection both at the input side of the Splitter and at the output side of the Splitter. Anyway, existing structure of Main Distribution Room (MDF) has its own protection against transient’s surges and discharges are being provided by the line circuit protection network. The Splitter contains no specific circuitry for this purpose.
Storage
Device storage temperature should be within the range - 45º C / + 70º C.
Mechanical Layout
The dimensions of Splitter itself are suitable to be able to be installed easily on the layout of ADSL Sub-rack.
Kepkep Group of Companies has been founded on 1961 by Ali Hamit Kepkep as a General Trade house. In 1983, the company has started the investment for the manufacture of dies & molds. Today the group is active in four different areas such as; import - export of automotive spare parts, precision die & molds, telecommunication connectors and accessories, medical blood collecting tubes and accessories. Following the pages below you may find out more about us.
sales@kepkep.com
export@kepkep.com
© 2021 - Kepkep İletişim Sistemleri İletişim İmalatı San. ve Tic. A.Ş - All Right Reserved.
